果冻视频

Vibration isolation kit for suspended installation to minimize vibration, ensuring quiet operation.

Speed controls are used for manual adjustment of the fan鈥檚 performance (for final system balancing) or to control the fan鈥檚 output in confined spaces, such as conference or meeting rooms. The fan can be adjusted to 60% of design airflow with a speed control. This reduction in airflow and fan speed is also accompanied by a reduction in noise level. Note: For use on direct drive fans with single phase, PSC or shaded pole motors.

Transformers are available for applications requiring voltage reduction. Selection is based on motor amperage. Rated for 115 to 230/277V, 6.5A.

Wall louvered discharge with anodized aluminum grille designed for exterior applications. Units feature built-in damper to eliminate backdrafts.

Motion detectors use a passive infrared motion detector to automatically turn the fan on when a change in motion is sensed. They have a viewing area of 180 degrees, however they must be placed in the line-of-sight. May be used with SP and CSP fans or fan/light combinations.

Dehumidistats are available with models SP and CSP fans to ventilate humid spaces. The sensor automatically detects excess humidity and activates a ventilation fan for control of excess condensation. There are automatic, manual, or air cycle modes. This can replace a single pole switch for control of a ventilating fan.

The Constant Airflow Control is used to monitor velocity pressure in a system, automatically adjusting the fan speed to maintain a desired velocity pressure (constant CFM). This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• Integral pressure transducer maintains compact form
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

The Constant Airflow Control is used to monitor velocity pressure in a system, automatically adjusting the fan speed to maintain a desired velocity pressure (constant CFM). This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Remote pressure transducer provides installation flexibility
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

NEMA-1 rated disconnect switch provides positive electrical shutoff and safety. Disconnect switches are a recommended and necessary safety feature for every fan. Mounted directly on the fan, within sight and reach, disconnect switches provide the best protection against accidental startup during service or inspection.

Switches may be used on model SP and CSP fans to enable manual control of your fan or fan and light combination. Single pole rocker switch assembly rated for 120-277V, 15A. UL Listed.

The Constant Pressure Control can be used to monitor static pressure in a system, automatically adjusting the fan speed to maintain a desired static pressure. This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• Integral pressure transducer maintains compact form
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

The Constant Pressure Control can be used to monitor static pressure in a system, automatically adjusting the fan speed to maintain a desired static pressure. This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• Integral pressure transducer maintains compact form
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

The two-speed control allows motor RPM (fan speed) to operate between two discreet speeds (A or B) through an SPDT switch or relay connected to the dry contact input or through wet voltage (115-230VAC) applied to the digital input terminal. This control accepts an input voltage of 115/208-240V and is intended for use with Greenheck's Vari-Green motor. Recommended for use in schools, restaurants, multi-family structures and condos where manual or demand controlled ventilation applications requiring high and low speed operation exist.

• Accepts input voltage of 85-277VAC
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

The Constant Pressure Control can be used to monitor static pressure in a system, automatically adjusting the fan speed to maintain a desired static pressure. This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Remote pressure transducer provides installation flexibility
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

Model MS-16 is a 1 Pole, single throw wall mount manual starter with pilot light. This starter supports up to 1/2 HP, 120 Volt, 1 Phase and includes a face plate.

When the temperature in the space rises above the set point of 50 F - 90 F the contacts close and the thermostat will signal the fan to come on in order to exhaust air from the space. Includes face mounted thermometer that displays room temperature.

Transformers are available for applications requiring voltage reduction. Selection is based on motor amperage. Rated for 115 to 230/277V, 8.6A.

Switches may be used on model SP and CSP fans to enable manual control of your fan or fan and light combination. Single pole light combination switch assembly rated for 120V, 15A. UL Listed.

Transformers are available for applications requiring voltage reduction. Selection is based on motor amperage. Rated for 115 to 230/277V, 4.3A.

The Indoor Air Quality Temperature / Humidity control monitors the temperature and/or the relative humidity in a space. It will automatically adjust the ventilation rate to or from a space by increasing or decreasing the speed of the fan based on the desired set point. Recommended for use in assisted living facilities, schools, prisons and buildings constructed of materials that are more sensitive to high moisture levels.

• Adjustments for set point, minimum and maximum fan speed
• Fan speed and temperature or humidity level are available as an analog output to read by a building automation system or secondary device.

The Constant Pressure Control can be used to monitor static pressure in a system, automatically adjusting the fan speed to maintain a desired static pressure. This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Remote pressure transducer provides installation flexibility
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

Adjustable for temperature ranges between 30潞F to 110潞F (-1潞C to 43潞C), 120V, 16 amp

Speed controls are used for manual adjustment of the fan鈥檚 performance (for final system balancing) or to control the fan鈥檚 output in confined spaces, such as conference or meeting rooms. The fan can be adjusted to 60% of design airflow with a speed control. This reduction in airflow and fan speed is also accompanied by a reduction in noise level. Note: For use on direct drive fans with single phase, PSC or shaded pole motors.

The Vari-Green remote dial control allows the user to manually adjust the fan's speed from a remote location. This control mounts to a wall using a 2x4 junction box and is supplied with a wall cover plate. Recommended for use in commercial buildings and restaurants.

The Indoor Air Quality VOC control senses the level of volatile organic compounds (VOCs) in a space and automatically adjusts the ventilation rate to the space by increasing or decreasing the speed of the fan based on the level of VOCs present. Up to 10,000 unique VOCs exist and Greenheck's VOC sensor can detect all of them. Recommended for applications experiencing intermittent human traffic including bathrooms, classrooms, cafeterias, or other spaces where quality of air is a concern.

• Adjustments for air quality setpoint, minimum and maximum fan speed
• Fan speed and VOC level are available as analog outputs to be read by a building automation system or secondary device.

The Constant Pressure Control can be used to monitor static pressure in a system, automatically adjusting the fan speed to maintain a desired static pressure. This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• Integral pressure transducer maintains compact form
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive

The Vari-Green remote dial control allows the user to manually adjust the fan's speed from a remote location. This control includes a countdown timer to automatically turn the fan off after 10, 30, 60 or 90 minutes. Recommended for use in commercial buildings and restaurants.

• Mounts to a single or multi-gang junction box
• Includes lockout feature to prevent tampering.

Hooded wall cap with rectangular duct connection designed for outside wall applications. Constructed of steel with black enamel finish, units feature built-in birdscreen and damper.

The Vari-Green transformer provides a 24-volt power source from the existing line voltage at the fan to the motor and controls. It has two dry auxiliary contacts (one normally open and one normally closed) available to signal a motorized damper or interlock with other devices.

The Constant Pressure Control can be used to monitor static pressure in a system, automatically adjusting the fan speed to maintain a desired static pressure. This control reduces energy consumption not only by reducing the speed and the energy used by the fan, but will also reduce the amount of conditioned air that is exhausted. Recommended for use in multi-family structures, hotels and schools where demand control ventilation applications exist.

• 2-line, backlit display
• Dedicated airflow control mode
• NEMA-4 enclosure on all components
• Pressure range of +/- 1.0 inch wg
• Remote pressure transducer provides installation flexibility
• Intended for use with Greenheck's Vari-Green motor and Vari-Green Drive